1-800-282-9290 FOR USI EDUCATION OR GOVERNMENT SALES 1-800-243-4565C A L L T O L L F R E EROLL LAMINATOR O W N E R S M A N U A LCSL2700
Thread the top roll of film under the idler roller as shown in the threading diagram on previous page (see Figure 9-4). Pull the film down so that th
HEAT SETTINGSPrior to laminating, allow the machine to pre-heat at least 15 minutes in order to stabilize the temperature. Temperature settings depe
SETTING TENSIONTo adjust tension for upper and lower rollers, the laminator must be loaded and heated. Remove the heat guard and feed tray. Loosen bo
1213Heat Shoe Guard Photo 13-3Photo 13-1 Feed Tray Photo 13-2
RELOADING A NEW ROLL OF FILM ON A HOT LAMINATORAllow the old film to run to a point just before it pulls off the cardboard cores. Turn the drive swit
CLEANING THE HEAT SHOESWith continuous use the heat shoes and rubber rollers may accu-mulate adhesive and dirt. It is recommended that you periodicall
UPPER HEAT SHOE REMOVAL INSTRUCTIONS 1. Unplug laminator and allow it to cool to room temperature.2. Remove the left side housing. First remove the th
TO REINSTALL THE HEAT SHOE 1. Be sure laminator is unplugged. 2. Guide heat shoe wires exiting from the left end of the heat shoe through the
REMOVING THE RUBBER ROLLERSNOTE: Only remove rollers if they are cut or in poor condition.NOTE: The following procedure removes all 4 rollers. In ce
STEP 8: Loosen the set screws of the lower roller sprockets (laminating roller shown) Photo 19-3.STEP 9: Loosen the Allen head set screws on the le
IMPORTANT INFORMATIONPLEASE DO NOT DESTROY THE SHIPPING CARTON!USI urges you to store the original carton in which your laminator was shipped. Should
STEP 11: To install a new roller or replace the original roller, reverse the removal procedure. Be sure to properly reposition the sprockets and align
PRESSUREThe pressure settings for the rubber rollers on USI Laminators are preset at the factory and should not require adjusting. In most cases, it
LAMINATOR LUBRICATION Oil the drive chain once every six months with a light weight oil.To avoid binding of the laminating and pull rollers, periodica
CLEANING FRICTION STUDSIf film rolls begin to shudder or squeak, cleaning of tension assembly is required. STEP 1: Remove the film rolls.STEP 2: Rem
REPLACING THE THERMOSTATStep 1: Unplug the laminator.Step 2: Remove the left side housing. See Upper Heat Shoe Removal Instructions (pg 16).Step 3: L
Photo 25-1Photo 25-2Photo 25-3Photo 25-4Photo 25-5Photo 25-62425
TIGHTENING SPROCKETSPhoto 25-1Laminating Roll SprocketPull Roll SprocketMotor SprocketSet ScrewLower laminating roll shaft.Flat SpotPhoto 25-3Photo 25
TROUBLE SHOOTINGCOMMON EXAMPLES OF POOR LAMINATING . . . and their causes.A. FILM NOT BONDING TO SUBJECT OR TO ITSELF AT SEALED EDGES Causes: 1.
TROUBLE SHOOTINGCOMMON EXAMPLES OF POOR LAMINATING . . . and their causes. (continued)G. HEAT DOES NOT WORK AND RED INDICATOR LIGHT DOES NOT ILLUMIN
CSL Series IV WIRING DIAGRAM2829CSL 2700 WIRING DIAGRAM
TABLE OF CONTENTSChapter 1 — Preparation Part I Laminator Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PARTS LIST Part # Component Description Per MachineLeft Zone A5510 HEAT SWITCH LIGHTED 2002 1 A5514 DRIVE SWITCH 2002 1 A5846 H
PARTS LIST (continued) Part # Component Description Per MachineCommon A4525 1/4 SPLIT LOCK WASHER 2 A4526 BLIND RIVET, GRIPPER DOG, TINNERMAN
USI Corporate Headquarters: 98 Fort Path Road Madison, CT 06443-2264 (203) 245-8586 • (800) 243-4565 • Fax 24 Hour (203) 245-7337East Coast Distributi
45SAFETY PRECAUTIONSWARNING: Please review the following safety precautions before unpacking your new laminator.• Use care in unpacking and lifting t
Feature Location: A Tension Adjusting Knobs B Color Coded Supply Mandrel (holds film) C Heat Guard D Side Housing E Temperature Adjustment
FIND A WORK AREAA separate work station is required to house your USI laminator. Ample room is necessary to access the laminator from all 4 sides. If
UNPACKING YOUR LAMINATOR Your laminator comes packed in one carton. It contains (1) laminator, (1) heat guard, (1) top supply mandrel, (1) bottom sup
LOADING FILMColor-coded laminators & film: (For more information on this revolutionary system see the back cover)Select the two rolls of laminatin
Note: When loading your laminating film, check for film splices. These rolls will be clearly marked. Splices are not common, but are unavoidable.
Komentáře k této Příručce